|
|
(per ASME Y14.5M-1994)
James D. Meadows
"BASICS" Set: $990.00
Master the Basics of Geometric Dimensioning and
Tolerancing in only Four Hours! Never Enough Time! There
is never a good time to get away for training. Yet, we
all know we'll do a better, more efficient job if
properly trained. What if great training were available
in a short, four-hour course right at your job site?
The information contained in the four hours of the GD&T
DVD "Basics" Course provide the basic
concepts/characteristics of GD&T and, specifically, the
logic and analytical reasoning behind choosing the best
controls, the best datums and the correct geometric
tolerances in GD&T. This short course would also make a
great GD&T refresher/reference on the ASME Y14.5M-1994
standard. Jim will lead you through a logical,
step-by-step progression of geometric part definition,
assembly analysis and the procedural requirements for
manufacturing and inspection. |
|
|
Attend training whenever
you have a few minutes, leave whenever you want and return to pick
up exactly where you left off. You don't have to complete it in one
sitting. You can put in the minutes you can spare away from the job
until you have completed the program. You can learn at your own
pace, at your work site or at home, replay any portion of the tapes
at your leisure and devote only the time you can afford.
It takes only four hours of your time and sells for a fraction of
the cost of the entire basic through graduate level training program
that we offer. Not everyone needs the advanced knowledge of
dimensioning and tolerancing techniques included in the full 12-tape
series. If you just need the basics, this program is for you; and,
of course, if you decide you want more advanced training later, we
have that, too.
With this dynamic GD&T BASICS DVD short course, you will receive the
following:
(4) DVDs - individually packaged and in a labeled box for easy
storage and identification (DVDs not sold individually) Click each
for details:
Lesson 1) The Major Principles
Lesson 4) The Basics of Symbology
Lesson 5) Allowed vs. Actual Deviation from True Position: Bonus
Tolerancing and Virtual Condition Boundaries
Lesson 6) Profile, Flexible Parts and Datum Targets
(1) Geometric Dimensioning and Tolerancing: Applications and
Techniques for Use in Design, Manufacturing and Inspection Text: (a
625-page hard cover text by James D. Meadows, based on ASME
Y14.5-1994); Published 1995 by CRC Press, Inc., New York, NY; ISBN:
0-8247-9309-9 (800) 272-7737, CRC Press
(1) Geometric Dimensioning and Tolerancing: Workbook and Answerbook:
(a 350-page soft cover workbook/ answerbook that corresponds to the
text referenced above--with some of the most complex, realistic
products and assemblies ever shown) --by James D. Meadows; Published
1996 by CRC Press, Inc., NY, NY ISBN: 0-8247-0076-7
PREVIEW THE SERIES...
Your Introduction to GD&T on multimedia Computer-Based
Training.
We can send you a 30 minute Introductory DVD which will
provide an overview of, and introduction to, the complex
design discipline of GD&T.
The Introductory material also introduces your
instructor, Jim Meadows (a nationally/internationally
recognized "expert" on the topic and an ASME Y14.5.2
Certified Senior Level GD&T Professional), the workshop
materials, the Y14 and B89 standards to be discussed,
and the logic behind the applications-based approach
that is used in the training sessions. It includes
actual excerpts from several of the 12 sessions.
This is an excellent introduction to GD&T for upper
management. |
|
If you have any questions about
GD&T training, books, workbooks, tests or DVDs,
please reach out to James D. Meadows & Associates, Inc., at (615) 924-3600.
|